Detailed Information for Jetweld LH-70
SDS ID: 0012
SDS Sheets

Supplier

Manufacturer

Language

Revision Date

Classification

Document Flags




Document Flags Legend

Icon Description

GHS Document

WHMIS Document
GHS


Signal Word



GHS Hazard Categories
N/A


GHS Hazard Statements
N/A


GHS Precautionary Statements

Prevention: N/A

Response: N/A

Storage: N/A

Disposal: N/A

PPE

Gloves

Goggles

Face Shield

Respirator

Apron

Ventilation: Use enough ventilation, local exhaust at the arc, or both to keep the fumes and gases from the worker's breathing zone and the general area. Train the welder to keep his head out of the fumes. Keep exposure as low as possible.
Wear protective gloves. Suitable gloves can be recommended by the glove supplier.
Do not eat, drink or smoke when using the product. Always observe good personal hygiene measures, such as washing after handling the material and before eating, drinking, and/or smoking. Routinely wash work clothing and protective equipment to remove contaminants. Determine the composition and quantity of fumes and gases to which workers are exposed by taking an air sample from inside the welder's helmet if worn or in the worker's breathing zone. Improve ventilation if exposures are not below limits. See ANSI/AWS F1.1, F1.2, F1.3 and F1.5, available from the American Welding Society, www.aws.org.
Protective Clothing: Wear hand, head, and body protection which help to prevent injury from radiation, sparks and electrical shock. See Z49.1. At a minimum this includes welder's gloves and a protective face shield, and may include arm protectors, aprons, hats, shoulder protection, as well as dark substantial clothing. Wear dry gloves free of holes or split seams. Train the welder not to permit electrically live parts or electrodes to contact skin . . . or clothing or gloves if they are wet. Insulate yourself from the work piece and ground using dry plywood, rubber mats or other dry insulation.
Wear helmet or use face shield with filter lens shade number 12 or darker for open arc processes - or follow the recommendations as specified in ANSI Z49.1, Section 4, based on your process and settings. No specific lens shade recommendation for submerged arc or electroslag processes. Shield others by providing appropriate screens and flash goggles.
Keep your head out of fumes. Use enough ventilation and local exhaust to keep fumes and gases from your breathing zone and the general area. An approved respirator should be used unless exposure assessments are below applicable exposure limits.
First Aid
See SDS
Product Details
SDSID
0012
Product Name
Jetweld LH-70
Synonyms
N/A
Internal Stock Numbers
Manufacturer Stock Numbers
Specific Gravity
1
Density lbs/Gal
Not Given
Physical State
Not Given
Pounds per Cubic Foot
Not Given
Odor
Not Given
Odor Threshold
Not Given
Solubility
Not Given
Partition coefficient Water/n-octanol
Not Given
Viscosity
Not Given
Color
Not Given
Flash Point
Not Given
Flash Point Method
Not Given
Boiling Point
Not Given
Boiling Range
Not Given
Melting Point
Not Given
Evaporation Rate
Not Given
Decomposition Temperature
Not Given
Auto-ignition Temperature
Not Given
LEL
Not Given
UEL
Not Given
Vapor Pressure
Not Given
Vapor Density
Not Given
pH
Not Given
Flammability
Not Given
VOC%
Not Given
Percent Volaitile
Not Given
Chemical Ingredients
Ingredient

CAS Number

Weight %

Carboxymethyl Cellulose, Sodium Salt 9004-32-4 0.1% - 1%
Feldspars 68476-25-5 1% - 5%
Fluorides (as F) 16984-48-8 5% - 10%
Iron 7439-89-6 50% - 100%
Iron Oxide 1309-37-1 0.1% - 1%
Limestone 1317-65-3 5% - 10%
Manganese 7439-96-5 1% - 5%
Potassium Silicate 1312-76-1 1% - 5%
Quartz 14808-60-7 0.1% - 1%
Silicon 7440-21-3 0.1% - 1%
Silicon Dioxide (Amorphous) 7631-86-9 0.1% - 1%
Sodium Silicate 1344-09-8 1% - 5%

Waste Codes
No Records Available