|Product Name||SDS ID||Manufacturer|
|ColorMaster With Covermax Technology Paint + Primer Gloss Hunter Green (52001)||0013||KRYLON Products Group|
|Spray Paint; Green Spray Paint; Green Paint; stuff; Krylon Colormaster with Covermax Technology Paint + Primer... (52001)||(216) 566-2117
GHS Hazard Catagories
FLAMMABLE AEROSOLS - Category 1
GASES UNDER PRESSURE - Category Compressed gas
SKIN CORROSION/IRRITATION - Category 2
EYE DAMAGE/IRRITATION - Category 2A
CARCINOGENICITY - Category 2
TOXIC TO REPRODUCTION - Category 2
SPECIFIC TARGET ORGAN TOXICITY (Single Exposure) - Category 3
ASPIRATION HAZARD - Category 1
SPECIFIC TARGET ORGAN TOXICITY (Repeated Exposure) - Category 2
SENSITIZATION - SKIN - Category 1
GHS Hazard Statements
Causes serious eye irritation
Causes skin irritation
Contains gas under pressure; may explode if heated
Extremely flammable aerosol
May be fatal if swallowed and enters airways
May cause an allergic skin reaction
May cause damage to organs through prolonged or repeated exposure.
May cause respiratory irritation; or May cause drowsiness or dizziness
Suspected of causing cancer
Suspected of damaging the unborn child.
GHS Precautionary Statements
Prevention: Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking; Do not spray on an open flame or other ignition source.; Pressurized container: Do not pierce or burn, even after use.; Wash hands thoroughly after handling.; Obtain special instructions before use.; Do not handle until all safety precautions have been read and understood.; Use only outdoors or in a well-ventilated area.; Contaminated work clothing must not be allowed out of the workplace.; Wear protective gloves. Wear eye or face protection. Wear protective clothing.; Do not breathe dust or mist.
Response: Get medical attention if you feel unwell.; If exposed or concerned: Get medical attention.; If inhaled: Remove person to fresh air and keep comfortable for breathing.; Call a POISON CENTER or physician if you feel unwell.; If swallowed: Immediately call a POISON CENTER or physician.; Do NOT induce vomiting.; If on skin: Wash with plenty of soap and water.; Wash contaminated clothing before reuse.; If skin irritation or rash occurs: Get medical attention.; If in eyes: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.; If eye irritation persists: Get medical attention.
Storage: Store locked up.; Protect from sunlight. Do not expose to temperatures exceeding 50 deg C/122 deg F.; Store in a well-ventilated place.
Disposal: Dispose of contents and container in accordance with all local, regional, national and international regulations.
General: Read label before use; Keep out of reach of children; If medical advice is needed, have product container or label at hand
|Environmental Exposure Controls:||Emissions from ventilation or work process equipment should be checked to ensure they comply with the requirements of environmental protection legislation. In some cases, fume scrubbers, filters or engineering modifications to the process equipment will be necessary to reduce emissions to acceptable levels.|
|Other Skin Protection:||Appropriate footwear and any additional skin protection measures should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product.|
|Respiratory Protection:||Based on the hazard and potential for exposure, select a respirator that meets the appropriate standard or certification. Respirators must be used according to a respiratory protection program to ensure proper fitting, training, and other important aspects of use.|
|Appropriate Engineering Controls:||Use only with adequate ventilation. Use process enclosures, local exhaust ventilation or other engineering controls to keep worker exposure to airborne contaminants below any recommended or statutory limits. The engineering controls also need to keep gas, vapor or dust concentrations below any lower explosive limits. Use explosion-proof ventilation equipment.|
|Hand Protection:||Chemical-resistant, impervious gloves complying with an approved standard should be worn at all times when handling chemical products if a risk assessment indicates this is necessary. Considering the parameters specified by the glove manufacturer, check during use that the gloves are still retaining their protective properties. It should be noted that the time to breakthrough for any glove material may be different for different glove manufacturers. In the case of mixtures, consisting of several substances, the protection time of the gloves cannot be accurately estimated.|
|Hygiene Measures:||Wash hands, forearms and face thoroughly after handling chemical products, before eating, smoking and using the lavatory and at the end of the working period. Appropriate techniques should be used to remove potentially contaminated clothing. Contaminated work clothing should not be allowed out of the workplace. Wash contaminated clothing before reusing. Ensure that eyewash stations and safety showers are close to the workstation location.|
|Eye/Face Protection:||Safety eyewear complying with an approved standard should be used when a risk assessment indicates this is necessary to avoid exposure to liquid splashes, mists, gases or dusts. If contact is possible, the following protection should be worn, unless the assessment indicates a higher degree of protection: chemical splash goggles.|
|Body Protection:||Personal protective equipment for the body should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product. When there is a risk of ignition from static electricity, wear antistatic protective clothing. For the greatest protection from static discharges, clothing should include anti-static overalls, boots and gloves.|