Product Summary Information
Product name
Rimadyl (Carprofen) Chewable Tablets
Signal Word
Warning
SDS ID
0021

Manufacturer
Zoetis Inc
PO BOX 651
Florham Park, NJ
07932
USA

Manufacturer Phone
(866) 531-8896


GHS Hazard Categories
TOXIC TO REPRODUCTION - Category 2
SPECIFIC TARGET ORGAN TOXICITY (Repeated Exposure) - Category 2
SENSITIZATION - SKIN - Category 1B


GHS Hazard Statements
May cause an allergic skin reaction
May cause damage to organs (digestive system) through prolonged or repeated exposure by ingestion.
Suspected of damaging the unborn child.


GHS Precautionary Statements

Prevention: Obtain special instructions before use.; Do not handle until all safety precautions have been read and understood.; Do not breathe dust/fume/gas/mist/vapors/spray; Wear protective gloves/protective clothing/eye protection/face protection.; Contaminated work clothing must not be allowed out of the workplace.

Response: If exposed or concerned: Get medical advice/attention.; If on skin: Wash with plenty of water.; If skin irritation or rash occurs: Get medical advice/attention.; Wash contaminated clothing before reuse.

Storage: Store locked up.

Disposal: Dispose of contents/container in accordance with local/regional/national/international regulations.

Location
Main Plant - LA
Main Plant - LA > Warehouse A
Main Plant - LA > Warehouse A > Building 1
Main Plant - LA > Warehouse A > Building 2
Main Plant - LA > Warehouse B
Main Plant - LA > Warehouse B > Building 3
Main Plant - LA > Warehouse B > Building 4
Main Plant - LA > Warehouse C
Main Plant - LA > Warehouse C > Building 5
Main Plant - LA > Warehouse C > Building 6
Main Plant - NY
Main Plant - NY > Control Center 1
Main Plant - NY > Control Center 1 > Unit 1
Main Plant - NY > Control Center 1 > Unit 1 > Equipment 1
Main Plant - NY > Control Center 1 > Unit 1 > Equipment 2
Main Plant - NY > Control Center 1 > Unit 2
Main Plant - NY > Control Center 2
Main Plant - NY > Control Center 2 > Unit 1
Main Plant - NY > Control Center 2 > Unit 2
Main Plant - NY > Control Center 2 > Unit 3
Main Plant - NY > Control Center 2 > Unit 5
Main Plant - Ontario
Main Plant - Ontario > Assembly
Main Plant - Ontario > Maintenance
Main Plant Corporate
Main Plant Corporate > Administration
Main Plant Corporate > Administration > Control Center 1
Main Plant Corporate > Administration > Control Center 1 > Unit 1
Main Plant Corporate > Administration > Control Center 1 > Unit 2
Main Plant Corporate > Administration > Control Center 2
Main Plant Corporate > Administration > Control Center 2 > Building 1
Main Plant Corporate > Administration > Control Center 2 > Building 2
Ingredient CAS Number Weight %
Magnesium Stearate
557-04-0
Unknown
Sucrose
57-50-1
Unknown
Carprofen
53716-49-7
Unknown
Corn Starch
9005-25-8
Unknown


PPE Phrase:
Thermal Hazards: Not applicable.
Eye/Face Protection: If contact is likely, safety glasses with side shields are recommended.
Other: Wear suitable protective clothing. Use protective clothing (uniforms, lab coats, disposable coveralls, etc.) in both production and laboratory areas.
Hand Protection: Wear appropriate chemical resistant gloves. Impervious gloves are recommended if skin contact with drug product is possible and for bulk processing operations.
Respiratory Protection: No personal respiratory protective equipment normally required. In case of insufficient ventilation, wear suitable respiratory equipment. Respiratory protection should be provided in instances where exposure to dust, mists, aerosols or vapors are likely. If the applicable Occupational Exposure Limit (OEL) is exceeded, wear an appropriate respirator with a protection factor sufficient to control exposures to below the OEL.
General Hygiene Considerations: Observe any medical surveillance requirements. Always observe good personal hygiene measures, such as washing after handling the material and before eating, drinking, and/or smoking. Routinely wash work clothing and protective equipment to remove contaminants. Contaminated work clothing should not be allowed out of the workplace.
Appropriate Engineering Controls: Good general ventilation (typically 10 air changes per hour) should be used. Ventilation rates should be matched to conditions. If applicable, use process enclosures, local exhaust ventilation, or other engineering controls to maintain airborne levels below recommended exposure limits. If exposure limits have not been established, maintain airborne levels to an acceptable level. General ventilation normally adequate.